Schritt-für-Schritt-Anleitung zur Verwendung der OpenWRT-Reset-Taste

The openwrt reset button lets you quickly return your router to factory settings. Resetting your openwrt router will remove all your changes. You should always save your settings before you reset. When you press and hold the openwrt reset button, you can bring back factory settings. You do not need any special tools. Most people reset their openwrt router by holding the button for 10 to 30 seconds. Watch the lights on the router to see when it resets. This reset works for both new and experienced users. Beginners can use the button to reset safely. Advanced users might pick harder ways to reset. Resetting your openwrt router helps if you forget your password or want a new start.

Wichtigste Erkenntnisse

• Always make a backup of your OpenWRT-Router settings before you reset. This will help you save your custom settings.

• Look for the reset button on your router. It is usually on the back, bottom, or side. You might need a paperclip to press it.

• Hold the reset button for 10 to 30 seconds. Watch the LED lights to start the factory reset process.

• After you reset, use the default login details. Change the password right away to keep your network safe.

• If the reset button does not work, try failsafe mode or reset using SSH. Check your router’s manual for special steps.

Find the Reset Button

Button Location

You need to find the reset button before you try any reset methods. Most routers have a small button on the back or bottom. Sometimes, you see the word “RESET” next to it. The button may sit inside a tiny hole. You might need a paperclip or pin to press it. Look for a round or square button that feels different from the power or WPS buttons.

Tip: Always unplug your router before you look for the reset button. This keeps you safe and helps you avoid pressing the wrong button.

You can check your router’s manual if you have trouble finding the button. Many guides show pictures of the button location. If you use a HUASIFEI 5G WiFi6 Router, you will find the reset button near the power port. This makes it easy to use different reset methods when you need to reset openwrt router settings.

Model Differences

Not all routers look the same. Some models have the reset button on the side. Others hide it under a sticker or label. You may see a button that needs a long press for some reset methods, while other models need a quick tap. Always check your router’s model number before you try to reset openwrt router devices.

Here is a quick table to help you:

You should know that reset methods can change based on your router’s brand and model. Some routers support more than one way to reset openwrt router settings. Always read the manual or visit the support website for the best reset methods.

Prepare to Reset

Backup-Einstellungen

Before you reset your OpenWRT router, you should always back up your settings. This step protects your custom configurations, so you can restore them after returning to factory settings. You have several reliable ways to create a backup:

1. Web Interface Method

   • Go to the router’s web interface.

   • Open the System tab and select Backup / Flash Firmware.

   • Click the GENERATE ARCHIVE button.

   • Download the backup file to your computer.

   • After you reset to factory settings, you can upload this file to restore your settings.

2. Command Line Method

   • Use SSH to connect to your router:
     ssh root@<openwrt>

   • Run this command to create a backup:
     sysupgrade -b /tmp/backup.tar.gz

   • Transfer the backup file to your computer using SCP or WinSCP.

   • You can open the backup with 7zip to remove files that might cause problems, like old web interface settings.

3. Manual Archive Method

   • Archive the /etc directory with:
     tar cvf /tmp/openwrt-etc.tar /etc/*

   • Use SCP to move the archive to your desktop.

Tipp: If you use extra storage, like a USB drive, you can move the overlay partition for larger backups. Tools like rsync help you schedule regular backups, so you never lose important data.

Note Default Credentials

After you reset your router to factory settings, the login details change. Most OpenWRT routers set the password to ‘password’ or leave it empty. You should check the login screen after the reset. Always change the default password right away to keep your network safe.

Remember: Write down the default username and password before you reset. This step helps you log in quickly after restoring factory settings.

Use the OpenWRT Reset Button

Resetting your openwrt router with the openwrt reset button is a simple process. You do not need any special tools or technical skills. You can follow these steps to return your device to factory settings. This reset process works for most models, including the HUASIFEI 5G WiFi6 Router.

Power On

First, make sure your router is plugged in and powered on. The reset process will not work if the router is off. Check that the power LED is lit. If you see no lights, plug the router into a working outlet and press the power button. Wait for the router to finish starting up before you begin the reset process.

Drücken und halten

Next, find the openwrt reset button on your router. Use a paperclip or pin if the button sits inside a small hole. Press and hold the button firmly. Most reset methods require you to keep the button pressed for a certain amount of time. For many routers, holding the button for 10 to 30 seconds will start the reset process. Some models, like the TP-Link MR3420, need about 10 seconds. Others, such as the Arduino Yun, may need you to hold the button for at least 30 seconds. You should keep holding the button until you see a change in the LED lights. This step is important for resetting your openwrt router to factory settings.

Tip: If you are not sure how long to hold the button, count slowly to 30. This covers most reset methods and helps you avoid an incomplete reset process.

LED Indicators

Watch the LED lights on your router during the reset process. The lights give you clues about what is happening. On some routers, you will see the LEDs blink slowly at first, then blink faster, and finally blink very quickly. For example, on the GL.iNet MT300N, the middle LED blinks about five times, then blinks faster, and finally blinks very fast before you release the button. Some routers show the power LED cycling between solid and blinking green. These patterns tell you that the reset process is working. The LED blinking may last a few minutes. When the lights change or turn off, the router is resetting your openwrt router and clearing your settings.

• Typical LED patterns during the reset process:

  • Slow blinking, then faster blinking, then very fast blinking

  • Power LED cycling between solid and blinking

  • All LEDs turning off briefly, then turning back on

If you do not see any LED changes, check that you are pressing the correct button and holding it long enough. The reset process depends on the model, so LED patterns may vary.

Release and Reboot

When you see the LED pattern finish, release the openwrt reset button. The router will now reboot on its own. This step completes the reset process. Wait for the router to power back up. The LEDs will return to their normal state when the router is ready. You can now access your router with the default settings. You do not need SSH or serial access for this reset process. The openwrt reset button gives you a quick way to reset openwrt-Router devices without extra tools.

Note: Do not unplug the router during the reset process or while it is rebooting. Interrupting the reset process can cause problems with your device.

After resetting your openwrt router, you will need to log in with the default credentials. You can now restore your backup or set up your network again. This reset process helps you fix problems, clear forgotten passwords, or start fresh with factory settings. If you have trouble, try the reset process again or check your router’s manual for special reset methods.

After Factory Settings

Default Configuration

When you finish resetting your router, it returns to its original state. All your changes disappear, and the system brings back the default environment. OpenWRT uses an overlay filesystem. This means the router wipes out any custom settings and restores the original files. You get the same setup as when you first took the router out of the box.

The firewall settings also go back to their defaults. The router loads the standard firewall rules from the original configuration file. This step helps your network stay safe and lets you access the internet again. You will see the default network settings, such as the IP address and DHCP server, just like when you first set up the device.

Note: After you restore factory settings, always check your network devices. Make sure they connect to the router using the new default settings.

Many users face a few common problems right after a reset:

• You might not reach the web interface at 192.168.1.1.

• The router could seem unresponsive, even with solid power lights.

• Confusion about which Ethernet port to use (WAN or LAN) can slow you down.

• Sometimes, the router does not recover, even after following the reset steps.

If you see these issues, do not worry. Most problems have simple fixes.

Access Router

You can access your router again after restoring factory settings. Follow these steps to get started:

1. Connect your computer to one of the LAN ports on the router.

2. Set your computer’s network settings to get an IP address automatically (DHCP).

3. Open a web browser and type 192.168.1.1 in the address bar.

4. Log in with the default username and password. Some routers leave the password blank after a reset.

5. If you cannot reach the web interface, try restarting your computer and router.

If you still have trouble, check the Ethernet cable and make sure you use a LAN port, not the WAN port. Sometimes, you may need to use special recovery steps, such as failsafe mode, if the router does not respond.

Tip: Always write down your new settings after you change them. This habit saves time if you need to restore factory settings again.

A quick table can help you remember what to expect after a reset:

You now have a clean slate. You can restore your backup or start fresh with new settings. Factory settings give you a safe and stable starting point every time.

Troubleshoot Reset Issues

Button Not Working

Sometimes, the reset button on your router does not work as expected. You might press and hold it, but nothing happens. This problem can happen for several reasons:

• The router may need you to hold the button for at least 10 to 15 seconds. Try using a paperclip and count slowly.

• Some devices, like the TP-Link MR200v1, only reset after holding the button for more than 5 seconds.

• If you updated your firmware or bootloader, the router might not respond to the reset button. Sometimes, a bug in the bootloader can damage memory blocks, stopping the device from booting.

• The reset script may have a problem. On some routers, a small change in the script can make the button too sensitive or not work at all.

If the button still does not work, you can try resetting your openwrt router using SSH. Connect to your router with a terminal or PuTTY, then run the factory reset command. This method helps when the physical button fails.

Tip: Always check the LED lights. If you see no change, the router may not be booting fully. In this case, the reset button will not work.

Failsafe-Modus

Failsafe mode gives you another way to fix your router if the reset button does not help. You can use this mode when you face problems like forgotten passwords or a bad configuration.

1. Power on your router.

2. Repeatedly press the reset button during startup until the LEDs start blinking. This means failsafe mode is active.

3. Connect your computer to the router with an Ethernet cable.

4. Open a browser and go to 192.168.1.1 or use SSH to connect.

5. If you cannot connect, set your computer’s IP address to 192.168.1.2 and try again.

Failsafe mode lets you access the router’s shell. You can fix settings or reset the device manually. This tool works best when resetting your openwrt-Router does not solve the problem.

Other Recovery Options

If both the reset button and failsafe mode do not work, you still have options. Many routers support advanced recovery methods:

1. Use the U-Boot bootloader menu. You can boot from an SD card or use TFTP to load new firmware.

2. Download the official firmware from the manufacturer’s website.

3. Set up a TFTP server on your computer and connect it to the router.

4. Power off the router, hold the reset button, and power it back on. Keep holding the button to start the firmware transfer.

5. Watch the TFTP server logs to confirm the process.

These steps help when you face serious issues, like a router that will not boot or respond. They are also useful for troubleshooting connectivity problems that simple resets cannot fix.

Note: Always follow the manufacturer’s instructions for advanced recovery. If you feel unsure, ask for help from support or the OpenWRT community.

HUASIFEI 5G WiFi6 Router & OpenWrt

Comprehensive Product Overview of the HUASIFEI 5G WiFi6 Router

Die HUASIFEI 5G WiFi6 Router helps you get a fast and steady network at home or work. It supports both 5G and WiFi 6, so you can enjoy quick internet and strong wireless signals. You can stream videos, play games, or connect lots of smart devices at the same time.

Here is a simple table with the main hardware features:

This router has a strong processor and lots of RAM for good performance. It comes with many antennas to help your signal reach farther. You can use SIM cards for mobile internet, which is helpful if your main internet goes out.

Tipp: This router is great if you need to connect many devices or want fast internet for work and fun.

Detailed Overview of OpenWrt Compatibility and Features

The HUASIFEI 5G WiFi6 Router works well with OpenWrt. You do not have to worry about it not working. You can use OpenWrt 21.02 or newer versions. There are easy guides to help you install OpenWrt using U-Boot, sysupgrade, or SSH.

OpenWrt gives you many cool features:

• Custom Firewall Rules: You can make your network safer.

• VLAN and QoS: You can control traffic and pick which devices are most important.

• VPN Support: You can make safe connections from far away.

• Client Management: You can see and manage all your devices.

• Web Interface: You can change settings easily, even if you are new.

You get a stable and flexible OpenWrt router. You can update firmware, switch networks, and use special tools without problems. This makes the HUASIFEI 5G WiFi6 Router a smart pick for people who want to control their wireless network.

If you want a router that works with OpenWrt right away, this one gives you strong features and peace of mind.

Tips and Precautions

Wann wird zurückgesetzt?

You might ask when you should reset your OpenWRT router. Many people reset after big firmware updates. These updates can change important parts of the system. If you install an older firmware, resetting helps your router work with old settings. Sometimes, problems happen that you cannot fix in simple ways. In these times, resetting gives your router a fresh start.

• Big firmware updates that change how things work

• Going back to an older firmware version

• Router will not save settings or you cannot reach it

• Strange problems that do not go away with easy fixes

Do not reset for small updates or tiny problems. Always write down your settings before you reset. Resetting will erase your changes and bring back factory defaults. This happens by erasing and making a new overlay partition in the router’s firmware. If your router will not save settings or stops working, resetting can help it work again.

Security After Reset

When you finish resetting, your router goes back to default settings. The default username and password are now active. If you do not change them, your router is not safe. Hackers or malware can get into your router’s settings. Some people think their home network is safe, but infected computers can still attack routers with default passwords.

Always make a strong and new password right after you reset. This keeps your network safe from bad people. If you use a router that someone else owned, resetting removes old data, but you should still change all passwords. Leaving the default password makes it easy for others to control your router and see your private stuff.

Here is a quick checklist for security after you reset:

Be careful after every reset. Good habits keep your network safe and your data private.

Sie können reset your OpenWRT router by doing a few easy steps. Make sure to save your settings before you begin. Write down the default username and password so you do not forget. If something goes wrong, look at the LED lights for clues. Try the tips for fixing problems if you need help.

If you need more help, check out these places:

• OpenWRT documentation and community forums

• Forums for your device or the Privacy Guides forum

• The OpenWRT GitHub issues page for bugs and questions

These places can help you fix most OpenWRT reset problems fast and safely.

FAQ

How long should I hold the OpenWRT reset button?

You should hold the reset button for 10 to 30 seconds. Watch the LED lights. When they blink quickly or turn off and on, you can release the button. This starts the factory reset process.

Will resetting my HUASIFEI 5G WiFi6 Router delete my files?

A factory reset removes your custom settings and passwords. It does not delete files on your computer or phone. Only the router’s configuration returns to default.

What should I do if the reset button does not work?

Try holding the button longer. If nothing happens, use failsafe mode or connect with SSH to reset. Check your router’s manual for special instructions. You can also contact HUASIFEI support for help.

Can I reset my OpenWRT router without the button?

Yes, you can reset using the web interface or SSH. Go to System > Backup / Flash Firmware and choose “Perform reset.” You can also run Erstboot oder jffs2reset in the command line.

What are the default login details after a reset?

Die meisten OpenWRT-Router use “root” as the username. The password is often blank or set to “password.” Always change the default password after your first login to keep your network safe.